Instruction manuals

Everything about setting, wearing and caring for your MSTR watch. Choose your model to see the right instructions straight away.

Choose your model

Not sure which type you have? Check the movement on the product page, or send us your order number via WhatsApp.

Quartz chronograph

Applies to: Ambassador · MK5 · GT · Ambassador X

Movement: Seiko VD53 (Ambassador, MK5, GT) · Miyota JS20 (Ambassador X)

Crown positions
  1. Position 0: normal wear
  2. Position 1: set the date
  3. Position 2: set the time
Setting the time
  1. First check AM/PM: the date should change around midnight, not at noon.
  2. Pull the crown out to position 2 when the second hand points to 12.
  3. Turn the crown to the correct time.
  4. Push the crown back to position 0, ideally in sync with a time signal. The second hand starts running again.
Setting the date
  1. Pull the crown out to position 1.
  2. Turn the crown until the correct date appears. If nothing happens, turn it the other way.
  3. Push the crown back to position 0.

Avoid setting the date between roughly 9 pm and 1 am, when the movement itself is changing the date.

Using the chronograph
  • Top pusher (A): start and stop.
  • Bottom pusher (B): reset to zero. Stop the chronograph first.

Don’t leave the chronograph running unnecessarily: it uses extra battery.

Resetting the chronograph hands

Are the chronograph hands not exactly at 12 after a reset, for example after a battery change or a knock? Here’s how to fix it:

  1. Pull the crown out to position 2 (the second click).
  2. Press button (A) or (B) to set the stopwatch hands to “0”. (A) moves them counter-clockwise, (B) clockwise.
  3. Push the crown back to position 0.

Automatic

Applies to: Ambassador Automatic · Voyager Automatic

Movement: Seiko NH35 (self-winding)

Crown positions
  1. Position 0: hand winding
  2. Position 1: set the date
  3. Position 2: set the time (second hand stops)
How an automatic works

An automatic has no battery. The movement winds itself through the motion of your wrist. Fully wound, it runs for about 41 hours. If you haven’t worn it for a day or two, it will have stopped. That’s normal.

A mechanical movement can gain or lose a few seconds a day. That’s normal too.

Winding
  1. Leave the crown in position 0.
  2. Turn the crown gently clockwise, about 20 to 30 times. There is no stop, so no need to force it.
  3. Then set the time and date.
Setting the time
  1. Pull the crown out to position 2. The second hand stops so you can set it precisely.
  2. Turn the crown to the correct time. Mind AM/PM: the date should change around midnight.
  3. Push the crown back to position 0.
Setting the date
  1. Pull the crown out to position 1.
  2. Turn the crown until the correct date appears. If nothing happens, turn it the other way.
  3. Push the crown back to position 0.

Don’t set the date between roughly 9 pm and 1 am. The movement is changing the date then and you could damage the mechanism. Move the time outside that window first.

Tips
  • Keep your automatic away from strong magnets such as speakers, tablet covers and magnetic clasps. Magnetism can upset its timekeeping.
  • Not wearing it every day? A watch winder keeps it running.

Skeleton automatic

Applies to: Noble Skeleton Automatic

Movement: Miyota 8N24 (self-winding, open movement)

Crown positions
  1. Position 0: hand winding
  2. Position 1: set the time
How an automatic works

The movement winds itself through the motion of your wrist and has no battery. Fully wound, it runs for about 40 hours. This model has no date.

Winding
  1. Leave the crown in position 0.
  2. Turn the crown gently clockwise, about 20 to 30 times.
Setting the time
  1. Pull the crown out to position 1.
  2. Turn the crown to the correct time. On this movement the second hand keeps running.
  3. Push the crown back to position 0.
Tips
  • Keep your watch away from strong magnets.
  • Through the open movement you can see the balance wheel ticking: a good sign it’s running.

Quartz

Applies to: DayTrip · Voyager · Noble · Ambassador Slim · Ultra Slim · Major

Movement: Japanese quartz movement by Seiko or Miyota

Crown positions
  1. Position 0: normal wear
  2. Position 1: set the date (and the day on some models)
  3. Position 2: set the time
Setting the time
  1. Pull the crown all the way out (position 2, or position 1 on a model without a date).
  2. Turn the crown to the correct time. Mind AM/PM if your watch has a date.
  3. Push the crown back to position 0.
Setting the date
  1. Pull the crown out to position 1.
  2. Turn the crown until the correct date appears.
  3. Push the crown back to position 0.

Avoid setting the date between roughly 9 pm and 1 am.

Setting the day (DayTrip, Major, Ambassador Slim)

In position 1, turn the crown the opposite way from the date. Does the day not change? Then advance the hands by 24 hours at a time in position 2 until the correct day appears.

More about your watch

Does your watch have a screw-down crown?

A screw-down crown is screwed tight against the case, which keeps water out better. You can tell because the crown can’t be pulled out straight away.

  1. Open: turn the crown counter-clockwise until it comes loose and pops out a little. This is position 0.
  2. Then set the time or date as described above.
  3. Close: push the crown in and turn it clockwise until it’s tight. Firm, but don’t force it.

Always screw the crown down again before your watch comes into contact with water.

Water resistance

The product page shows whether your model is water resistant to 5 ATM or 10 ATM.

5 ATM10 ATM
Washing hands, rainYesYes
Showering (not hot)YesYes
Swimming, snorkellingNoYes
Diving, sauna, hot tubNoNo
  • Never use the crown or pushers under water.
  • Rinse your watch with lukewarm fresh water after salt water or chlorine.
  • Leather straps are not suitable for water.
Changing and shortening straps

Changing a strap (quick release)

  1. Turn the watch over. On the back of the strap, next to the case, there is a small pin.
  2. Slide the pin inwards with your fingernail and remove the strap.
  3. Attach the new strap the same way and let the pin click back into place.
  4. Give the strap a gentle pull to check it is secure.

Shortening a steel bracelet

  1. Many steel bracelets come with a free screwdriver.
  2. Unscrew the small screw in a link and remove the link. Take the same number of links from both sides of the clasp so it stays centred.
  3. Reattach the bracelet and tighten the screw firmly.

Rather not do it yourself? Any jeweller or watchmaker can do it quickly.

Battery (quartz)
  • A battery usually lasts 2 to 3 years, less if you run the chronograph often.
  • Have the battery replaced by a watchmaker, who can also check the water resistance.
  • The battery is not covered by the warranty.
  • Chronograph hands not at zero after a battery change? Follow the steps under “Resetting the chronograph hands”.
Care
  • Steel and titanium: polish with a soft microfibre cloth. At 10 ATM you can rinse the case and a steel bracelet with lukewarm water and a little mild soap.
  • Carbon and rubber: wipe with a damp cloth and let them air-dry.
  • Leather: keep it dry, out of strong sunlight and away from perfume.
  • Storage: dry, out of direct sunlight and not next to magnets or phones.
Troubleshooting
My automatic has stopped.
It isn’t wound enough. Turn the crown clockwise about 20 to 30 times in position 0 and set the time again.
The date changes at noon.
AM/PM is set wrong. Turn the hands forward 12 hours in position 2.
The chronograph hands aren’t at zero.
Reset them with the steps under the quartz chronograph.
The crown won’t pull out.
Your watch probably has a screw-down crown. Unscrew it counter-clockwise first.
My watch runs fast or slow.
On a quartz watch the battery is often nearly empty. On an automatic a few seconds a day is normal; if it suddenly runs much faster, it may be magnetised.
There is condensation under the glass.
Stop wearing the watch and contact us.
Warranty and service

Every MSTR watch comes with a 2-year warranty from the date of purchase, with a valid proof of purchase. If something is wrong, send us your order number and a photo or video and we’ll find the best solution together.

Still stuck?

Send us your order number and a photo or video of your watch. We are happy to help.

Contact us